Buttons Won't Respond. If the cycle already started before buttons stopped responding, you may be pressing some options that cannot be added, or the child lock option is.

If you're having an issue with your Samsung washing machine or dryer and you're not sure what the issue is, try checking for an error code using the Smart Ca. Unbeatable deals, free delivery and price match on the best range of cookers, ovens, washing machines, fridge freezers and more. Find everything you need at appliancentre.com or visit us in our Finchley store. Whirlpool washing machine error codes. Find out the meaning of the Whirlpool washer error code your machine is dispaying and fix it today. Possible Cause: The lid is not closed properly Solution: Make sure that the lis is closed properly and press the START/PAUSE button.After starting a cycle, it may take a few moments before the tub begins to turn or spin. The washer will not spin unless the lis is locked.

Whirlpool washing machines with RA appliance

All error codes that may occur in the washing machine during its independent diagnosis, as a rule, are indicated in the instructions that are attached to the washing machine when it is purchased. But, unfortunately, there are times when the instruction is lost during a repair or relocation.

Our table contains codes and combinations for all models of washing machines from this manufacturer. In this table, we described in detail what each code and each combination means and what to do to return the washing machine to working condition.

Washing Machine Caddy Error Codes Free

Error Code	Problem	Repair
F/H	No water detected entering machine or Pressure switch trip not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. OR If the control has turned the water valve. on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.	Press PAUSE/CANCEL twice to clear the display. If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves Verify inlet valve operation If there is water in the unit: Verify Drain pump operation. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch Verify there is not a siphon problem Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU) Check all hoses for possible leaks Verify pressure switch operation Verify flow meter operation Verify CCU operation
F/02	Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and “F/02” is flashed. NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.	Press PAUSE/CANCEL twice to clear the display. Check the drain hose and make sure it is not plugged or kinked. Check the electrical connections at the pump and make sure the pump is running. Check the drain pump filter for foreign objects. If the above does not correct the problem, replace the pump.
F/05	Water Temperature Sensor Error If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the “F/05” error code will be displayed.	Check the Water Temperature Sensor, Heating Element and Element Relay. Check connections to the Sensor, Heating Element and Relay.
F/06	Drive Motor Tachometer Error The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.	Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). Check the Drive Motor Check the MCU Check the Wire Harness
F/07	Motor Control Unit Error The Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.	Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the MCU Check the Drive Motor Check the Wire Harness
F/09	Overflow Condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.	Check the drain hose and make sure it is not plugged or inked. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU). Check/Clean Drain Pump Filter of foreign objects Check for Drain Pump Failure Check the Inlet Valve for proper shut off Check the Pressure switch for proper operation
F/10	Motor Control Unit (MCU) Heat Sink Thermal Trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an “F/10” will be displayed.	Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. Check Wire Harness connectors to the MCU, and Central Control Unit (CCU) Check the Drive system for any worn or failed components Check MCU Check Motor
F/11	Serial Communication Error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.	Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) Check the Drive system for any worn or failed components Check MCU Check CCU Check Motor Check Wire Harness
F/13	Dispenser Circuit Error If the dispenser motor is not able to be driven to its proper position.	Check mechanical linkage from dispenser motor to the top of the dispenser. Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) Check Dispenser Motor
F/14	EEPROM Error The Central Control Unit (CCU) receives its data from an EEPROM on board the CCU. If there is an error reading this data, it will cause this error.	A power glitch may cause this error. Try unplugging the Unit for two minutes to see if that fixes the error. Check CCU
F/15	Motor Control Unit (MCU) Error If the MCU detects multiple resets or errors during a wash c